Bracelets · November 16, 2026 · 0 views

Bracelets: Plating: Microns, Wear and the Returns You Avoid - HOLYCOME

Bracelets: Plating: Microns, Wear and the Returns You Avoid - HOLYCOME

Plating is the cheapest line on a bracelets quote and the most expensive to get wrong. A 0.3 micron difference decides whether a piece survives a season or comes back as a tarnish complaint.

What the micron number means

Plating thickness is measured in microns, one thousandth of a millimetre. On bracelets, 0.3 micron is a fashion finish, 0.5 is a season, 0.8 to 1.0 is daily wear, and 1.5 and above is the jewelry standard for a plated piece sold as long-wear.

Ask for the number per finish, not per factory. Rhodium, gold tone and e-coat have different targets.

Build the landing date from ship date plus transit plus clearance. Planning from the ship date alone makes every season a week late.

The four failure modes

First, tarnish at the contact points: the shank inner face, the clasp and the ear post. Second, plate skip at the prong tips. Third, colour drift between lots. Fourth, blistering after the e-coat.

Each has a cause: insufficient thickness, poor pre-plate cleaning, bath chemistry drift, or cure temperature. A bracelets claim sheet should name the cause, not just the defect.

FinishThicknessExpected lifeUse
Rhodium, thin0.3 micronOne seasonFashion
Rhodium, standard0.8 micronDaily, 12+ monthsCore line
Gold tone0.5-1.0 micronSeason to dailyCore line
E-coat over plate+2-3 micronTarnish barrierHumid markets

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Put the gram weight per size on the PO, not an average. Cost and feel both follow weight, and an average hides the size that breaks the margin.

Specifying plating in the PO

Write four lines: base metal preparation, plating type, thickness in microns, and the wear test. Add the salt-spray or wear-hour standard you will accept.

Then test the first lot: rub the contact points with a cloth for 30 seconds and check for colour transfer. A simple test catches most thin-plate lots.

Repair and replating policy

Plated goods need a replating path. Ask whether the factory will replate a returned piece and at what cost. A supplier with no replating service leaves you to absorb the return.

For bracelets at volume, a replating agreement is worth more than a 3 percent price concession.

Freight is a planning line, not an emergency line. A carton that lands two weeks early costs less than one that lands two days late.

What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Ask for microns per finish, not a trade name.
  • Test contact points on the first lot.
  • Write the wear standard into the PO.
  • Agree a replating path and price.
  • Check colour drift against the approved sample.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

Frequently Asked Questions

How thick should bracelets plating be?

0.8 micron rhodium for daily wear, 0.5 for a seasonal line, 1.0 or more for long-wear claims.

Why does plating wear at the shank first?

It is the contact point with skin and other rings. Thickness and pre-plate cleaning decide how long it lasts.

Can plating be reapplied?

Yes, if the base metal is clean. Ask for the replating cost and turnaround before you need it.

Does e-coat change the colour?

It can add a slight warmth. Ask for a coated sample before approving the colour.

Is thicker plating always better?

Up to a point. Too thick a plate can look heavy and can crack at the prong tips if the deposit is stressed.

What is the fastest way to lose money on a first order?

Skip the trial lot and accept an average gram weight. Both hide the problem until rework is at lot scale.

Send the bracelets finish requirement. We return the micron spec per finish, the wear test standard and the replating terms. See the full range at Bracelets and HOLYCOME.

None of this is exotic. It is a document, a measurement and a date, repeated until it becomes a process.

Need a quote for your next order?

Get Wholesale Pricing

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .