Earrings · November 16, 2026 · 0 views

Earrings: Size Consistency: The Spec That Decides Your Return Rate - HOLYCOME

Earrings: Size Consistency: The Spec That Decides Your Return Rate - HOLYCOME

On earrings, size is the number one return reason that has nothing to do with taste. A half-size drift inside one lot is enough to turn a clean program into a stream of exchanges.

Where size drift comes from

Three sources: the mould or CAD allowance, the polishing loss at the inner face, and the size stick used at the bench. On earrings, a 0.15 mm polishing loss is half a US size on a ring.

Ask which size standard the factory works to, US, UK or EU, and whether the stick is calibrated. Factories that answer vaguely are measuring by feel.

Set the reorder point from sell-through and lead time, not from the MOQ. Stock cover is a calculation, not a feeling.

Specifying the size run

Write the size curve, not just the range: for example US 5 to 9 with 20 percent at 6 and 7, 15 percent at 5 and 8, and 10 percent at 9. A flat curve leaves you with the extremes unsold.

Add the tolerance: plus or minus 0.1 mm on the inner diameter, measured after polishing, on earrings.

MeasureToolToleranceFrequency
Ring inner diameterRing gauge±0.1 mm10 per size
Chain lengthTape±5 mm10 per SKU
Clasp openingCaliper±0.2 mm5 per SKU
Ear post lengthCaliper±0.5 mm10 per SKU

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Put the gram weight per size on the PO, not an average. Cost and feel both follow weight, and an average hides the size that breaks the margin.

Incoming measurement

Measure ten pieces per size with a ring gauge or caliper at the inner diameter. Record the result by size. A lot that drifts at one size is a mould problem; a lot that drifts across all sizes is a stick problem.

For chains and bracelets, measure the clasp and the total length, and check the extension chain if the design has one.

Repair and resize policy

Ask whether the design can be resized, and by how many sizes. An eternity band or a full-channel setting often cannot. That limitation belongs in the listing, not in the return conversation.

On earrings, a resizable design is worth a small price premium because it removes a whole category of returns.

Freight is a planning line, not an emergency line. A carton that lands two weeks early costs less than one that lands two days late.

What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Name the size standard in the PO.
  • Write the size curve, not only the range.
  • Measure after polishing, not before.
  • Record drift by size, not as an average.
  • State resize limits in the listing.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

Frequently Asked Questions

Why do earrings sizes vary inside one lot?

Usually polishing loss at the inner face or an uncalibrated size stick. Ask for the post-polish measurement.

Should I use US or EU sizing?

Use the market you sell into. For US retail, US sizing with a stated tolerance is the cleanest.

Can a ring be resized after plating?

Yes, but the plating at the joint needs rework. Ask for the replating cost before you promise a resize.

How many pieces should I measure?

Ten per size for a first lot, five per size after that, plus every piece in a complaint sample.

What tolerance is realistic?

Plus or minus 0.1 mm on the inner diameter after polishing is a fair commercial standard.

What belongs in the first email to a new supplier?

Spec, quantity, target price, delivery date and the QC standard. Five lines get a useful reply.

Send the earrings size range and market. We return the size curve, the tolerance sheet and the resizing limits for each design. See the full range at Earrings and HOLYCOME.

None of this is exotic. It is a document, a measurement and a date, repeated until it becomes a process.

Need a quote for your next order?

Get Wholesale Pricing

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .