Jewelry Sets · November 16, 2026 · 0 views

Jewelry Sets: Custom: From CAD to Production Without Losing the Design - HOLYCOME

Jewelry Sets: Custom: From CAD to Production Without Losing the Design - HOLYCOME

A custom jewelry sets fails in one of two places: the CAD is approved before the stone is sourced, or the bench 'adjusts' the model to make it castable. Both are avoidable with a staged approval.

Stage one: the brief that survives translation

Give the factory five inputs: reference image, stone size in millimetres, metal and karat, finger size or chain length, and the retail price ceiling. Without the price ceiling, the CAD comes back beautiful and unmakeable at your margin.

Ask for a dimensioned drawing, not a render. A render hides the gallery height and the prong thickness, which are the two places a design fails.

Sample by size run, not from one mixed tray. Defects cluster by size and by design, and a mixed sample hides both.

Stage two: CAD approval with three checkpoints

Checkpoint one is stone seat depth: the stone must sit below the prong tips. Checkpoint two is minimum wall thickness at the shank. Checkpoint three is the casting allowance, usually 3 to 5 percent shrink.

Approve in writing at each checkpoint. A single 'looks good' message on jewelry sets is how a 1.8 mm shank becomes 1.4 mm after polishing.

StageDeliverableApproval gate
BriefDimensioned drawingStone size, metal, ceiling
CADSTEP file, wall thicknessWritten sign-off
Wax or printPhoto of the modelSeat and prong check
First articleOne cast piecePorosity and size check
BatchProduction runAQL inspection

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Keep the CAD file and the mould receipt. Ownership is a document, not an understanding.

Stage three: wax, cast and the first article

Ask for a photo of the wax or the resin print before casting. Ask for the first cast piece before the batch. That first article is where you catch porosity, a shifted seat or a prong that is too short.

Only after the first article passes should the batch run. Skipping it saves three days and costs a full lot.

Stage four: who owns the model

The CAD file is an asset. Put ownership in writing: the buyer owns the model after the mould fee is paid, and the factory will not reuse it for another client.

Without that clause, your custom jewelry sets can appear in another buyer's catalog two seasons later.

The specification is the product. Two pieces built to the same six lines are the same product even when the price differs; two built to different lines are not.

What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Give five inputs, including the price ceiling.
  • Approve a dimensioned drawing, not a render.
  • Check stone seat depth and wall thickness.
  • Photograph the wax before casting.
  • Put CAD ownership in the contract.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

Frequently Asked Questions

How long does a custom jewelry sets CAD take?

Three to seven days for a first model, longer if the stone has to be sourced first.

Who should own the CAD file?

The buyer, after paying the mould fee. Ask for the clause in writing before the first order.

Can I reuse the mould for another size?

Often yes, with a size adjustment. Ask whether the factory charges a new mould for a size change.

Why does the cast piece come out smaller?

Casting shrink, typically 3 to 5 percent, plus polishing loss. The CAD should carry the allowance.

What if the first article fails?

Fix the model, re-cast, and do not release the batch. A failed first article is the cheapest failure you will get.

How do I compare two quotes for this item?

Split both into metal, stone, labour, finishing and overhead, then compare line by line. A single total hides the specification difference.

Send the jewelry sets reference image and stone size. We return a dimensioned CAD, a first-article photo and the mould fee quoted separately. See the full range at Jewelry Sets and HOLYCOME.

The short version: specify the number, seal the sample, inspect against both. Everything else is negotiation.

Need a quote for your next order?

Get Wholesale Pricing

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .