Moissanite · November 16, 2026 · 0 views

Moissanite: QC and AQL: How to Set an Inspection Standard Buyers Can Enforce - HOLYCOME

Moissanite: QC and AQL: How to Set an Inspection Standard Buyers Can Enforce - HOLYCOME

Most moissanite disputes are not about workmanship. They are about a standard that was never written down. An AQL sheet turns 'it looks off' into a measured accept or reject decision both sides can live with.

What AQL actually means on jewelry

AQL is the acceptable quality limit: the percentage of defects a lot may carry and still pass. On moissanite, AQL 2.5 for major defects and AQL 4.0 for minor is the common commercial setting.

The number matters less than the definition. A loose stone is a major defect. A 0.2 mm polish mark on the gallery is minor. Write both into the sheet.

Sample by size run, not from one mixed tray. Defects cluster by size and by design, and a mixed sample hides both.

The four defect classes

Critical: sharp edge, wrong alloy, missing stone, nickel release above limit. Major: loose stone, wrong size, plating skip visible at arm's length. Minor: light polish mark, small bubble in the plate. Cosmetic: a mark only visible under a loupe.

Each class needs its own limit and its own remedy. A moissanite lot that fails critical fails entirely, whatever the AQL number says.

Defect classExampleLimitRemedy
CriticalWrong alloy, missing stone0Reject lot
MajorLoose stone, wrong sizeAQL 2.5Remake or credit
MinorPlating skip, light markAQL 4.0Price allowance
CosmeticLoupe-only polish markNot countedNote only

Read the table as a checklist rather than a recommendation. The right row depends on the price band, the wear pattern and the channel you sell into.

Put the gram weight per size on the PO, not an average. Cost and feel both follow weight, and an average hides the size that breaks the margin.

Sampling that matches the lot size

For 50 pieces, inspect all. For 500, sample 50 by ISO 2859 general level II. For 5,000, sample 80. Inspect by size run and by design, not from one mixed tray.

Photograph the defects you find, with the PO number in frame. A claim without a photo pack is a conversation, not a claim.

Making the standard stick

Put the AQL sheet in the PO as an annex. Require the factory's own inspection record with the carton. Hold the last 10 percent payment against the inspection result.

That structure is what turns a moissanite QC clause from a sentence into a lever.

The channel decides the tolerance. A boutique forgives a loupe mark; a marketplace does not. Build the inspection standard to the strictest channel you sell.

What to check before the order

Run the five checks below in order. The first two protect the money, the last three protect the launch date.

  • Write the defect definitions into the PO annex.
  • Sample by size run, not from one tray.
  • Photograph every defect with the PO number.
  • Hold final payment against inspection.
  • Keep the factory's own QC record with the carton.

If a supplier cannot answer three of the five, treat the quote as a starting point rather than a plan. Ask again in writing and keep the answer with the PO.

Frequently Asked Questions

What AQL should I use for moissanite?

AQL 2.5 major and 4.0 minor is the common commercial setting. Critical defects are zero regardless of the AQL.

Do I need a third-party inspection?

For the first two lots, yes. After that, your own incoming check plus the factory record is usually enough.

What counts as a loose stone?

Any stone that moves under light finger pressure, or shows a gap at the prong seat. Test every stone in the sample, not one per tray.

How do I handle a failed lot?

Reject, document, and agree remedy in writing: remake, credit or rework at the factory's cost. Do not accept a discount on a critical defect.

Can QC be done at the factory?

Yes, and it should be, but your inspection is the one that releases payment. Two checks catch more than one.

How do I know a supplier is reliable?

Two clean repeat lots and two on-time shipments. Before that it is a sample, not a supplier.

Send the moissanite spec. We return the AQL annex with defect photos, sampling plan and the remedy matrix you can attach to the PO. See the full range at Moissanite and HOLYCOME.

The short version: specify the number, seal the sample, inspect against both. Everything else is negotiation.

Need a quote for your next order?

Get Wholesale Pricing

Written by the Holycome manufacturing & quality team. Every figure and claim in this article comes from our own production floor in Wuzhou, China — in-house casting, stone setting and a three-pass quality inspection we have run since 2008.

Materials are tested for nickel, lead and cadmium release by SGS and CTT International; moissanite centre stones ship with their GRA warranty card and report. We also hold an independent SMETA / Sedex ethical-trade audit and a Hong Kong Customs AML registration.

Reviewed for accuracy by our quality team before publication. Last updated .