A customer asks: “Can I wear my moissanite ring every day?” The answer is yes—but with three caveats that most online product pages leave out. If you sell moissanite without setting those expectations, you will get the return request six months later when a stone chips on a thin girdle. Here is the honest durability briefing to put in your care card and to say out loud at the counter.
Hardness: the best among affordable stones
Moissanite measures 9.25 on the Mohs scale. To put that in context: diamond is 10, sapphire and ruby are 9, moissanite sits between them. Cubic zirconia is 8–8.5, and will scratch visibly in a pocket after a year. Moissanite resists scratching by dust (quartz at Mohs 7), by keys, and by incidental contact with most surfaces. For a daily-wear ring, it is the second-best jewelry stone commonly available, and the Wikipedia on moissanite entry confirms the Mohs rating that sets it apart from CZ, glass and crystal alternatives.
That hardness is why moissanite settings—not the stone—are the part that wears out. Read our metals guide for the prong-wear side of the story: a 9.25-hardness stone in a 2.5-hardness 14K gold setting means the prongs deform long before the stone scratches.
Toughness: the caveat
Hardness and toughness are different. Moissanite is hard but brittle. A sharp blow to a thin girdle or a pointed pavilion can chip the stone, especially on very thin 1.5 mm girdles cut for maximum apparent size. This is rare on a well-set solitaire with a protective basket, but it is a real risk on fashion rings with large stones on thin bands, or on stones used in tennis bracelets that take knocks against desktops and gym equipment. If you sell moissanite tennis bracelets, spec a minimum 2.0 mm girdle and price the band with enough metal to protect the edges.
Heat sensitivity
Moissanite is stable in normal wear, but it is not solder-friendly. Direct torch heat above roughly 600°C can fracture or discolor SiC. When a customer brings a ring in for prong repair, tell your bench jeweler to remove the stone before soldering, or use a heat shield. This is also the reason moissanite should not be autoclaved in a dental sterilizer and should be kept away from open-flame jewelry repair setups. Compare this to diamond, which survives direct torch work; moissanite needs the stone out of the setting for any bench procedure that involves heat.
Cleaning and maintenance
- Ultrasonic: generally safe for moissanite in a secure setting, but avoid if the stone has visible chips or the prongs are loose. The vibrations can widen an existing chip.
- Steam cleaner: use cautiously; rapid heat cycling can stress a chipped stone. For new, well-set stones it is fine.
- At home: warm water, mild dish soap, soft brush. No special polish needed. The GIA 4Cs care guidance for diamond applies equally to moissanite.
Compare this to diamond, which survives ultrasonic, steam, and almost any bench procedure. Moissanite is more delicate in the workshop, even though it looks tougher than most other customer stones. The distinction is worth telling customers so they do not bring the ring back for prong repairs without warning the bench about the stone material.
Frequently asked questions
Will moissanite scratch over time?
Not in normal daily wear. At Mohs 9.25, only diamond (10) will scratch it.
Can moissanite chip if I hit it?
Yes, especially on a thin girdle or a sharp side impact. It is hard, not indestructible.
Is moissanite safe in an ultrasonic cleaner?
Yes, in a well-set stone. Skip ultrasonic if prongs are loose or the stone is already chipped.
Can I wear moissanite in the shower or at the gym?
Yes. Soap, sweat and chlorine do not damage SiC. Remove it before heavy lifting or contact sports where knocks are likely.
How does this compare to CZ?
CZ scratches at Mohs 8.5 and fogs; moissanite stays clear. For daily wear, moissanite is a different class of stone—see our CZ vs moissanite bench test.
The care card you hand customers should cover three things: daily wear (fine, remove for heavy knocks), cleaning (warm soapy water, soft brush), and bench repair (remove the stone before soldering). That is the same guidance diamond houses use, adapted for SiC’s lower heat tolerance. If you offer in-store prong repair, train the bench to pull the stone first; if you outsource repair, write “moissanite—remove before heat” on the work order so the receiving jeweler does not torch the setting with the stone in it.
For resellers, the durability story is also a positioning point. Moissanite at 9.25 is the second-hardest jewelry stone in common use, and that comparison—not the price—is what justifies a $200+ retail ticket against cubic zirconia fashion jewellery at $20. Train sales staff to open with the Mohs rating, then the fire, then the price. Customers who hear the numbers first buy on value; customers who hear price first compare against CZ and walk.
Wholesale CTA: HOLYCOME ships moissanite with a minimum 2.0 mm girdle on all stock sizes and includes a care-card template with every bulk order. Request the care-card PDF when you ask for the price list, and compare girdle specs in our MOQ tiers.

