Two rings can look identical on a website and weigh 4 grams and 2.2 grams respectively. The difference is construction: one is cast from a wax, the other is stamped from a sheet of metal. Customers feel it within a week. Buyers spec it before they order.
Cast (lost-wax / investment casting)
Casting is the default for 90% of the wholesale moissanite pieces sold today. A wax model is injected, invested in plaster, burned out, and filled with molten metal. The method produces detailed heads, comfort-fit shanks, and complex shapes - it is the only way to make a solitaire with a hidden halo or a twisted vine band. A cast comfort-fit solitaire in 10k gold weighs 3.5-4.5 grams.
The weaknesses: castings can hide porosity (tiny gas bubbles inside the metal), and the surface finish depends heavily on how well the factory finishes the piece after shakeout. Cheap castings show a slight orange peel under magnification. Good castings are indistinguishable from milled metal to the naked eye, and they cost less than hand fabrication because the bench time is short.
Stamped (pressed from sheet)
Stamping cuts a ring shape from a flat sheet of sterling silver or gold-filled stock and rolls it into a circle. It is the cheapest way to make a simple band - a 2mm stamped silver band weighs 1.8-2.5 grams and costs $4-8 in workmanship. Stamped bands are thin, light, and visible from a mile when held next to a cast band.
Stamping works for stackable bands, midi rings, and thin gold-fill fashion pieces. It does not work for engagement mounts: the sheet metal is too thin to hold prongs reliably over years of wear, and the seam where the band is rolled is a structural failure point. If a supplier quotes a solitaire mount as "stamped," ask for photos - you probably do not want it.
Hand-fabricated
Hand fabrication builds the ring from raw wire and sheet: the bench solders the head, rolls the shank, and finishes each piece by hand. A hand-fabricated 6mm comfort-fit band weighs 5.5-7 grams and carries a workmanship fee of $60-150 per piece, versus $15-30 for a casting. The weight and the feel are unmistakable, and resizing is simple because the metal is dense and uniform.
Hand fabrication is worth it for bridal, men's bands, and any piece priced above $800 retail. It is overkill for $80 studs. The right mix for most boutiques is cast for 80% of the line, stamped for thin stackables, and hand-fabricated for the top 10-15% of bridal SKUs.
Weight reference by construction
Use these as a sanity check when a supplier quotes a mounting. A 2mm comfort-fit sterling silver band weighs 1.8-2.5g stamped, 2.5-3.5g cast, and 4-5g hand-fabricated. A 6mm 14k men's comfort-fit band weighs 4.5-6g cast and 7-9g hand-fabricated. A solitaire head in 14k with a 6-prong setting weighs 0.8-1.2g cast; a hand-fabricated head on the same shank adds another 0.5-0.8g. If a quote comes in 25% below those weights, the factory has either gone very light on metal or substituted a different construction. Ask for the spec sheet before you commit.
How construction affects resizing and repair
Cast bands resize cleanly up or down about two sizes, because the metal is uniform. Stamped bands resize poorly - the seam splits, and the thin shank cracks when bent. Hand-fabricated bands resize almost indefinitely, because the bench can add or remove metal from a dense shank. That matters for your return policy: a stamped stackable band that needs a size exchange is almost a write-off, while a cast or hand-fabricated solitaire can be resized in-store for $20-40 and sold again.
Settings tell the same story. A cast head with cast prongs wears down in about 5-8 years of daily wear. A hand-fabricated head with applied prongs can be retipped once or twice before the head is rebuilt. For engagement pieces, the applied-prong head is the difference between a 10-year warranty and a 3-year one.
How to verify the construction you paid for
Ask the supplier for the weight on the spec sheet, and check it on arrival. A cast 10k solitaire that lands at 2.8 grams instead of 4.0 has either been cast thin or swapped for a stamped mount. Weighing on a $20 digital scale takes 10 seconds per piece and catches the substitution before the piece hits the case. For buyers building a program, the same check applies across moissanite rings, bracelets, and pendants - weight is the honest number, not the photo. Spec the construction you want on the PO, then verify the weight; the two together are what keep a $400 mount from arriving as a $220 piece. Over a year, the difference between a cast band that holds its finish and a stamped one that splits at the seam is the difference between a customer who comes back and one who does not.
For third-party reference, the Wikipedia article on moissanite details moissanite’s discovery, optical properties and use in jewellery.
Frequently Asked Questions
How do I verify a factory before placing a bulk order?
Request a production video, business license, export records and a paid sample run. A factory that accepts a 50-piece test order is usually a real manufacturer.
What payment terms do you offer?
30% T/T deposit with the balance against the bill of lading. This protects both sides on first orders and can move to net terms after a track record.
What is your normal reject rate?
3–5% under 10x loupe inspection for cast and set pieces. Defective units are replaced free in the next shipment.
Where is the factory located?
Wuzhou, Guangxi, China—the core lab-grown and moissanite manufacturing cluster. Shipments go via Guangzhou or Shenzhen ports.

