A jeweler in Denver told us he was asked, at a bridal show, to identify a customer's 1.5ct round as "real or fake." He pulled out a 10x loupe, looked for about fifteen seconds, and said moissanite. The customer asked how. The answer was not a single inclusion - it was a pattern: facet edges looked slightly doubled, the surface had a faint growth-line texture, and the pavilion showed a tiny polishing streak diamonds rarely show. This is what magnification actually reveals, and it is a skill every retailer should own because customers ask, usually at the most inconvenient moment.
GIA grades diamonds under 10x magnification as the standard, and that same power is enough to separate a well-cut moissanite from a diamond. GIA's discussion of inclusions and clarity explains the diamond side; moissanite has its own signatures. Below is what the trained eye looks for.
Doubling of facet edges
The classic tell. Because moissanite is doubly refractive (refractive index splits along two axes at about 2.65 and 2.69), the back facets appear doubled when viewed through the crown at a 10x loupe. Diamond is singly refractive, so facet edges look single. Hold the loupe perpendicular to the table, look through the pavilion, and trace one back facet - if it looks like two parallel lines, that is moissanite. This is the single fastest ID. Note that a small number of diamonds with strong fluorescence or unusual strain can show weak doubling, but it is not the clean double image moissanite produces.
Surface texture and polishing marks
Lab-grown moissanite is cut from boule. Under 10x you often see fine parallel polishing striae on the table and crown, and occasionally a faint "growth hill" texture where the cutter chased a surface inclusion. Diamond surfaces, by contrast, show more irregular etching channels and naturals. Moissanite also polishes to a very flat, almost glassy surface - some buyers describe it as "too perfect." Read the material side in moissanite composition and sparkle.
Inclusion types
Diamonds carry feathers, crystals, clouds and chips shaped by natural growth. Moissanite carries needle-like growth tubes, tiny black graphite specks, and occasional stress halos around the culet. A stone loaded with feathers is almost certainly diamond; a stone with long thin needles and small black dots is usually moissanite. Clarity grades are assigned differently - see batch-to-batch clarity grading. One practical tell: moissanite inclusions tend to be aligned parallel to the boule growth direction, while diamond inclusions are irregularly oriented. If you see a row of tiny black dots in a straight line, you are almost certainly looking at silicon carbide.
Facet junctions and culet alignment
A well-cut moissanite shows sharp, crisp facet junctions where two polish planes meet. A poorly cut stone shows rounded or frosted junctions, which happens when the cutter chased a heavily included rough and lost the ideal angles. Culet alignment is another check: a centered culet sits directly under the table; an off-center culet is visible at 10x and signals a rough stone that did not yield ideal orientation. These are not gemological-grade observations, but they are the difference between a $40 stone and a $120 stone on the bench. Retailers who train their eyes here can spot a budget-cut stone before they quote it to a customer.
Thermal and tester behavior
A thermal diamond tester will read moissanite as diamond (it measures heat conductivity, and moissanite is similar). A modern dual thermal/electrical tester separates them - see what a jeweler's tester actually shows. But magnification is faster, free, and never needs a battery. Walk through the side-by-side retail case in moissanite vs diamond for buyers.
FAQ: moissanite vs diamond under magnification
Is facet doubling visible on every moissanite?
On most well-cut rounds, yes. Very small stones (under 3mm) and heavily included stones can mask it. For a 6.5mm round, doubling is the standard ID at 10x.
Can a diamond ever show doubling?
Rarely. Diamonds with strong strain or unusual growth zoning can show weak doubling, but it is not the clean double line moissanite shows. Confirm with a dual tester if unsure.
Does 10x magnification reveal poor cut on moissanite?
Yes. Windowing, off-center culets, and misaligned facet junctions are visible at 10x. A well-cut moissanite shows sharp facet junctions and a centered culet.
Should retailers own a 10x loupe?
Yes - it is a $20 tool that pays for itself the first time a customer asks "is this real?" Knowing the difference is a trust-builder, not a sales problem.
Stock moissanite that reads clean under a loupe. HOLYCOME cuts rounds, ovals and cushions with tight facet alignment and controlled doubling visibility, so your bench reads consistent stone to stone, batch to batch, order to order, every time. Request a sample today and inspect it yourself with your own 10x loupe.
Frequently Asked Questions
Is moissanite a good diamond alternative for retail buyers?
Yes for price-sensitive customers who want brilliance and hardness. Moissanite ranks 9.25 on the Mohs scale, holds up to daily wear and costs a fraction of a natural diamond of the same size, so it resells fast in bridal and fashion lines.
What is the minimum order for wholesale moissanite?
MOQ starts at 50 pieces per design for stock items. Custom cuts and private-label settings usually start at 100–300 pieces depending on the mold.
Do you provide certificates with moissanite stones?
Yes. Every parcel ships with GRA or IGI documentation listing carat weight, color grade and cut. We recommend passing the certificate to your end customer for trust.
How long does sample and bulk production take?
Samples ship in 3–5 days. Bulk runs take 15–20 days under 500 pieces, and 25–30 days for custom work.



